Move to the text

One in screw diagnosis result

1.4 mirihira head for the G-Shock GA2000 camera back

Materials SUS
Screw shape
1.4 millimeters of pace 0.45 millimeters tapping B types
The head shape There is R slightly, and are 0.7 millimeters of 4 millimeters of the zeroth special Hiller head diameter rustic buntings mortar pans?
0.45 millimeters of 1.4 millimeters of screw diameter B type pace
Screw 6 millimeters in length 
As a Casio G-Shock GA2000 camera back stopping screw customization
It was an inquiry of the production right or wrong with titanium.
The item on display plus (it was), but is (-) as there seemed to be (-) in an aspect early on a deadline
I suggested it.
As there are not a tapping screw, the results with titanium, it is honest uneasiness.
I can mold the mountain corner similar to SUS, or how is the duty (the anti-slack) as the screw?
In examining the cost as it takes it.

2 millimeters of Sarah heads for the Mamiya camera

Materials Iron
Screw shape
0.4 millimeters of 2 millimeters of pace small screw
The head shape 3 millimeters of the zeroth one kind Sarah head diameter
2 millimeters of screw diameter
Screw 12 millimeters in length (as Sarah full length) 
Screw around 2 millimeters in length
Use I am used by the connection part of a camera body and the lens
It was not in us
As a head was standardized goods, arrangement was possible by order.
I was consulted whether there was slightly long 15 millimeters in total.
In being different in materials, and this place being stock in us, and having you look at the sample.

0.6 millimeters for the watch camera back? 0.7 millimeters?

Materials Stainless steel
Screw shape
0.15 millimeters of 0.6 millimeters of pace or
0.175 millimeters of 0.7 millimeters of pace
The head shape * Sarah - head diameter 1.25 
Screw diameter 
If judge it from pace; of 0.6 millimeters
Was a screw, but outer diameter is big for 0.6 millimeters when measure; 0.7 millimeters?
Screw around 2 millimeters in length
Use Watch camera back stopping screw
The thread becomes round, too
That it is 0.6 millimeters being 0.7 millimeters or either
Because do not become clear, to user
I will have you try both.

2 millimeters for the Lenovo notebook PC

Materials Is it stainless steel? Is it iron (there are some magnetism)?
Screw shape With small screw M2 pace 0.4 slack inhibitor
The head shape
3,505 * Hiller diameter 3.5 rustic bunting 0.5 
The cross hole size first
Screw diameter M2 .0
Neck lower 5 millimeters in length
Use Lenovo note PC
With the prevention of slack (blue part)
Article low special a rustic bunting
Because may be head diameter, the point with the limit of the rustic bunting, a thing smaller than a current article melts; about the prevention
I suggest a by yourself commercial lock agent of user with by application.
I will have you try it in 2x5 made of titanium which there was in us. TA-00052
Head diameter 3.0 rustic bunting 0.6 
The cross hole size zeroth

1.2 millimeters for the watchstrap

Materials Stainless steel
Screw shape 1.2 millimeters of pace 0.25
The head shape I am subtracted by the head pear axis
Screw diameter M1 .2
Axle diameter φ around 1.38 millimeters
Axis around 21.5 millimeters in length
Screw around 2 millimeters in length
Use Watchstrap
The watch connection has much minus.
It considerably became the answer by the production to article without being found with the existing article.

Matsumoto Sangyo of the screw
1380-5, Okahotto, Abiko-shi, Chiba


<< the handling product >>
●Small screw
(millimeters/inch UNC UNF)
●Microscrew miniature screw
●Slack setscrew "nojirokku" 
●The slack prevention processing (adhesive system, application system)
●Tapping screw
●Rivet  ●Pin
Custom screw custom tailoring screw
●Screw for the animal experiment 

●Study use screw

<< the handling materials >>
* Iron 0 stainless steel 0 brass
* Titanium 0 aluminum
* Copper 0 phosphor bronze

I take the factory tour
How do you make the screw?
Of this
How do the materials say?

 Please refer.

TEL 04-7182-4490

It is the verge of the inquiry
Even if it is not the drawing of the screw 
Even a handwritten painting is OK.
If understand an image; the trace

I will blow it up.

Do not have any problem.
FAX 04-7182-2382




Back to TOP