Move to the text

One in screw diagnosis result

Parts of the motorcycle (discontinuance of making model)

Materials Aluminum
Screw shape
M14 pace 1.0 (specially?)
The head shape Is it a hexagon hole pan? Is it Hiller?
Motorcycle (discontinuance of making model)
It was the talk that I changed the product made in aluminum to the product made in stainless steel and wanted to make.
As for this
It is several that are necessary.
It has been cost over
It did not lead to production and became only the screw diagnosis.

Parts of the motorcycle gear part

Materials Iron
Screw shape
Inch screw UNF1/4-28 (rather thin screw) 
The head shape There is saliva in a hexagon
UNF1/4-28x70 millimeters (full length)
Parts of the motorcycle gear part 
I put it through the nut of UNF1/4-28, and a screw part becomes clear
The pace of UNF1/4-28 is Mt. 1 inch of 25.4 millimeters ÷ 28 = 0.907 millimeters
Screw 1/4 inch outside diameter is 1 inch of 25.4 ÷ 4 = 6.35 millimeters
It is 6.35 millimeters of screws of the thickness if I repair it to millimeters.
A use having possibilities to say a motorcycle, and having been one or the uneasiness that I could clear on the strength side,
It was several that were necessary, and an equal article has been a cost overcoat even if I produced it
It did not lead to production and became only the screw diagnosis.

As a thumbscrew substitute

Materials Is it iron?
Screw shape
Inch screw UNF#8-36x3/4 (rather thin screw) 
The head shape The shape that it is easy to pick up
UNF#8-36x3/4 inch (19.05 millimeters)
Thumbscrew of a certain machine 
I put it through the nut of UNF#8-36, and a screw part becomes clear
The pace of UNF#8-36 is Mt. 1 inch of 25.4 millimeters ÷ 36 = 0.7055 millimeters
In fact, as for this, there is a thing near the pitch (0.7 millimeters) of the regular eyes screw of M4
I judge that I can substitute it in M4x20 when I see it only with a screw.
I suggested it in this which circulated as there was the hope of the budget.
With the cap head of the head which I seem to be able to pick up about the head.
I switch to materials stainless steel.

The screw which turns off a watch and "the battery presser bar" in the watch

Materials Is it iron?
Screw shape
0.8 millimeters (0.20 millimeters of pace) 
The head shape Hiller head minus
The screw diameter both 0.8 millimeters (0.2 millimeters)
One screw length is 1.2 millimeters of screw parts with a shoulder screw 2 millimeters one more 
The screw which turns off a watch and the battery presser bar in the watch 
At screw around 0.77 millimeters outside diameter a square nut (TN-00005) of M0.8 in us
As I went when I put this, I judged it to be a screw of M0.8.
As it was the screw which stopped a board, head diameter was to be important, too.
As I have the budget, I stop the production and suggest an imitation from we stocks
There were 0.8x2 of the cross hole 00th of 1.8 millimeters of head diameter and 0.8x2.1 of the cross hole zeroth.
I had you choose 0.8x2.1(TE-00088) of the cross hole zeroth.
When head diameter did not match, I seemed to do something with a washer.

Mt. MTB aluminum inch screw UNF1/4-28 pan head

Materials Aluminum
Screw shape
Inch screw UNF 1/4-28 mountain (0.90 millimeters of pace) narrowed eyes screw
The head shape 3.25 millimeters of special pan hexagon hole 12.75 millimeters rustic buntings
Screw diameter UNF 1/4-28 mountain narrowed eyes pace 28 mountain/inch (0.90 millimeters)
Screw 5.5 millimeters in length 
MTB front suspension use 
A hexagon hole transforms a lot of disassembly frequency by maintenance and seems to want to grow it.
Aluminum → It was an inquiry of the production right or wrong with the stainless steel.
What kind of implication would it have that there was a through-bore in the center?
Scupper kitokadeshoka.
As I could cope on the strength side of the thing which I could produce in the same way or was anxious
After having had user understand confirmation,
Other than stainless steel, I examined even titanium, aluminum.

Matsumoto Sangyo of the screw
1380-5, Okahotto, Abiko-shi, Chiba


<< the handling product >>
●Small screw
(millimeters/inch UNC UNF)
●Microscrew miniature screw
●Slack setscrew "nojirokku" 
●The slack prevention processing (adhesive system, application system)
●Tapping screw
●Rivet  ●Pin
Custom screw custom tailoring screw
●Screw for the animal experiment 

●Study use screw

<< the handling materials >>
* Iron 0 stainless steel 0 brass
* Titanium 0 aluminum
* Copper 0 phosphor bronze

I take the factory tour
How do you make the screw?
Of this
How do the materials say?

 Please refer.

TEL 04-7182-4490

It is the verge of the inquiry
Even if it is not the drawing of the screw 
Even a handwritten painting is OK.
If understand an image; the trace

I will blow it up.

Do not have any problem.
FAX 04-7182-2382




Back to TOP